1. What is needed for processing?

Scissors or cutter knife, ruler or Meterstab, pencil and a plastic squeegee. A squeegee is a rubber spatula, and is in the handicraft business in the construction or available.You can also contact us.


2. How should the bonding surface be designed?
Surface should be smooth, dust-and grease-free, untreated wood (particleboard, plywood) should be used with a primer (Admission Reason / acrylic base) pretreatment.

3. As I cut right?
With ruler and pencil, any request form on the reverse side of paper, and then pre-cut be helpful here is the schedule grid. If you have precise edges to achieve financial statements, you should always consult with an overhang of about 4 mm cut. The protruding edge at the end with a sharp knife (cutter) cut.


4. How can I air bubbles when gluing to avoid?
At best, only a portion of the back to remove paper, foil, and then create a squeegee or a cloth from the center to the sides, the film press. Did the film not done properly, it can again be removed and corrected (with the exception of paper and paperboard). You achieve the best results if you smooth out a small, square balks, with a soft carpet covered the rest will be used.


5. Schief pasted, what can I do?
No problem, the film can be carefully removed and re-attached (except paper and cardboard) - the full adhesive strength develops only after several hours.


6. Can I also rounded edges umkleben?
Of course! This film during processing with a hair dryer on the lowest level of heat in the desired shape, and press. If the film is heated, it can be easy to take corners and edges. Here proceed cautiously so that the foil is not too much is overstretched.

7. How heat resistant are the d-c-fix ® films?
The foil keeps temperatures up to 80 ° C short-term problems from.

8. Can I use dc-fix ® films in wet process areas?
Of course! If water is often directly linked to the film edges (eg on the tub edge) should be with silicone / Kaltschweissmittel be pasted over.

9. How do I remove old self-adhesive film?
Just a corner of the foil pull starting. An easy film dissolves in heated state (again, use a hairdryer). Any adhesive residue can use alcohol-based solvent removed.

10. Can I d-c-fix ® films cleaned?
Yes, dc-fix ® films are compatible with all commercial cleaning products to clean - is best suited to warm water and a little dishwashing detergent. Moist areas with a soft cloth to dry.

11. How environmentally friendly are d-c-fix ® films?
dc-fix ® films are heavy-metal-free, lightfast according to DIN EN ISO 105-B02, as well as abrasion and friction determined according to DIN EN ISO 105-X12. It will only be solvent-free dispersion adhesive is used. Also in the nursery area are dc-fix ® films when used safely.

12. As I have a glue film on glass surfaces (without bubbles)?
It's simple: First, the surface to stick with commercial cleaners to clean thoroughly. Then the surface with water spülmittelversetztem wet, back paper completely from the slide away, slide perhaps even wet. The film on the water film and to the desired position. Now the water and air to exhaust out the sides (with a squeegee or a cloth). Any opacification of transparent film to disappear at an ambient temperature of 20 ° C after 10-13 hours.

 


13. Are there any dc-fix ® film, which protects from the sun?

Yes, dc-fix ® sun protective effect due to a metallized surface heat way back, absorbs 99% of UV rays and allows only 20% of light through the windows.

14. How can I remove self-adhesive film?
The self-adhesive film in a deduct the starting corner. An easy film dissolves in heated condition (here, use a hairdryer). Any adhesive residue can use alcohol-based solvent removed.

15. How is the self-adhesive foil from dc-fix ® glass processed?
This film is liable complete without adhesive. The glass surface for a better sliding only a few drops of water and detergent with a spray bottle wetted. Then the foil from the back paper off and carefully on the glass surface position. Water and air with the blade attached to the outer sides ausgestrichen - The foil holds!

16. How can a film with no adhesive liable?
The film is liable by electrostatic adhesion. The simple contact between the film and the smooth and clean glass surface is enough to reach the liability.

17. How can the self-adhesive film be removed?
The foil is easy and residue-free from the glass surface deduct. The special feature: the film can as often re-placed and re-used.

18. How is the temperature-resistant self-adhesive film?
The foil keeps temperatures from - 10 to + 50 ° C easily made.

19. Bubbles! How do I get rid of?
With a needle and broach the air hole to the press.

20. Does the film also outdoors?
Yes. Depending on weather conditions (sun, water, fog ...) keeps the film about one to three years, after possibly changing the color and the slide can be harder.

21. Can I use dc-fix ® films in wet process areas?
Of course! If water is often directly linked to the film edges (eg on the tub edge) should be with silicone / Kaltschweissmittel be pasted over.

22. Can I d-c-fix ® films cleaned?
Yes, dc-fix ® films are compatible with all commercial cleaning products to clean - is best suited to warm water and a little dishwashing detergent. Moist areas with a soft cloth to dry.

23. As I lay the floor tiles?

The most beautiful Verlegeoptik arises when the space center will be started. Protective paper simply subtract the first tile at the intersection of the center of the room to create and press firmly, without additional glue to use.


24. On which floor adhesive floor tiles can be relocated?

Requirement is a solid, dry, smooth, flat and clean surface. The floor tiles can be especially well on concrete floors, screeds, wood flooring, laminate, PVC and linoleum floor coverings embarrassed. Unsuitable soils with floor heating, the outdoor area, the soils are exposed to constant moisture and not fortified soft substrates.

25. How are maintained floor tiles?
The soil should be regularly swept or be sucked. Depending on your needs they can with warm water and a mild cleaner moist soil will be wiped.